電工鋼硅鋼片：磁性能7.1.1 在 6.3 條件下提供的冷軋取向電工鋼的特性應符合表 3、湖北武漢表 4、湖北武漢表 5、湖北武漢表 6、湖北武漢表 7、湖北武漢表 8 和表 9的規定，時效試樣也應滿足這些特性。對帶有涂層的產品，絕緣涂層的質量應被計算在內。7.1.2 表 3、湖北武漢表 4 和表 6 中的普通型、湖北武漢高磁極化強度型、湖北武漢耐熱刻痕磁疇細化型產品的磁性能應該按 GB/T3655 測試，在測試前，試樣應在制造方提供的條件下進行應力退火（通常應力退火溫度的范圍為 800℃±20℃，退火時間為 2h，退火后隨爐冷卻）；但表 5 中的非耐熱磁疇細化法（如激光刻痕）生產的產品磁性能應按照 GB/T 13789 測試，試樣在測試前不需要進行應力退火。經供需雙方協商，表 3、湖北武漢表 4 和表 6 中產品的磁性能也可按照 GB/T 13789 測試。7.1.3 表 7、湖北武漢表 8 和表 9 中各系列產品的磁性能檢測方法，按產品類型對照本文件第 7.1.2 條款的規定執行。7.1.4 在磁場強度 H ＝ 800 A/m 條件下測試所得的磁極化強度 J800應符合表 3、湖北武漢表 4、湖北武漢表 5、湖北武漢表 6、湖北武漢表 7、湖北武漢表 8 和表 9 的規定，其中，同一產品按 GB/T 13789 方法所測得的磁極化強度值 J800比 GB/T 3655 方法所測得的磁極化強度值偏低。7.1.5 同一產品在磁極化強度 1.7T、湖北武漢同城頻率 50Hz 或 60Hz 條件下，按 GB/T 13789 方法所測得的 50Hz 和60Hz 條件下比總損耗值，參照 IEC 6040-8-7 Edition 5.0 2020-09 中規定的轉換系數 Fc＝0.925 進行轉換，轉換后的 P1.7/50和 P1.7/60應符合表 3、湖北武漢同城表 4、湖北武漢同城表 5、湖北武漢同城表 6、湖北武漢同城表 7、湖北武漢同城表 8 和表 9 的規定

電工鋼硅鋼片Electrical steel, also known as silicon steel sheet, is an indispensable metal material in the power, electronics, and military industries, and is also the largest functional material in production. It is mainly used as the iron core for various motors, generators, and transformers. Specific total loss (iron loss) is the total power consumed per unit mass of material when the magnetic polarization waveform remains sinusoidal, with a specific peak and frequency. The specific total loss is represented by the symbol P (Jm/f), in W/kg. Example: P1.5/50 represents the specific total loss at a maximum magnetic polarization intensity of 1.5T and a frequency of 50Hz. 3.2 Magnetic Polarization Q/BQB 480-20212 Magnetic polarization intensity refers to the peak magnetic polarization intensity of a specific magnetic field intensity when a sample is subjected to alternating magnetization. Its symbol is J (H), and the unit is T (Tesla). Example: J5000 represents the peak magnetic polarization intensity corresponding to a magnetic field intensity peak of 5000A/m. The material grades in this document are classified based on the nominal maximum specific total loss P1.5/50 (W/kg) at a magnetic polarization strength of 1.5T and a frequency of 50Hz, as well as the nominal thickness of the material. They are further divided into three categories based on product characteristics: ordinary type, stress relief annealing type, and high-efficiency type. Example 1: B35A210 represents a common non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 2.10W/kg； Example 2: B35AR300 represents a stress relieved annealed non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific total loss value P1.5/50 is 3.00W/kg； Example 3: B35AH230 represents an efficient non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. Example 4: 35WW210 represents a normal type WW non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.10W/kg. Example 5: 35WH230 represents an efficient WH non oriented electrical steel with a nominal thickness of 0.35mm, and the maximum nominal specific loss value P1.5/50 is 2.30W/kg. The classification and code of insulation coatings shall comply with the provisions of Table 2. Table 2 Classification and Code of Insulation Coatings Type Code Characteristics of Insulation Coatings Semi organic Thin Coating A Improves Punching Performance and Has Good Weldability Semi organic Thick Coating H has Good Punching Performance and High Interlayer Resistance Semi organic Chromium Free Thin Coating K does not contain chromium and has good weldability Semi organic Chromium Free Thick Coating M does not contain chromium and has good insulation performance Semi organic Chromium Free Extreme Thick Coating J does not contain chromium and has excellent insulation performance Semi organic Chromium Free Ultra Thick Coating L does not contain chromium and has extremely high insulation performance Self adhesive Coating